Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 72

Страница: 72 / 116

MAINTENANCE AND LUBRICATION

Lubrication Recommendations

Front Drive Axle

U Joints (1)

Grease

Locate grease fitting and grease

with grease gun.

Every 3 months

or 50 hrs

Rear Axle Bear-

ing (2)

Grease

Locate fitting on eccentric and

grease with grease gun.

Every 3 months

or 50 hrs

Swing Arm

Bushings (3)

Grease

Locate fitting on swing arm and

grease with grease gun.

Monthly or at 20

hrs

Middle Axle

Bearings (4)

Grease

Locate fitting on eccentric and

grease with grease gun.

Every 3 months

or 50 hrs

Center Swing

Arm Housing (5)

Grease

Locate fitting on swing arm hous-

ing and grease with grease gun.

Every 3 months

or 50 hrs

Rear Strut (6)

Grease

Locate fitting on rear strut and

grease with grease gun.

Every 3 months

or 50 hrs

More often under severe use, such as wet or dusty conditions

Grease conforming to NLGI No. 2, such as Conoco Superlube M or

Mobilegrease Special

Use Polaris Premium U-Joint Lube every 500 miles, before long periods of

storage, or after pressure washing or submerging.

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды

Polaris Light Utility Hauler 6x6, Руководство пользователя

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды