Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 74

Страница: 74 / 116

MAINTENANCE AND LUBRICATION

Lubrication Recommendations

Front Gearcase Lubrication

The front gearcase lubricant level

should be checked every six

months or 1000 miles (1600 km),

whichever comes first. Front

gearcase oil should be changed

annually.
1. With the vehicle on a level

surface, remove fill plug (1).

2. View the oil level and add oil

if needed. Oil should be kept

at the bottom of the fill plug

thread.

NOTE:

Use GL5

80-90 Weight Gear Lube (see

page 106).

3. Replace the fill plug.

Gearcase Oil Changing Procedure

1. Remove the fill plug.
2. Remove gearcase drain plug located on the bottom right-hand side

and drain the oil.

3. Clean and reinstall the drain plug and tighten securely (14 ft.

lbs./1.93 kg m).

4. Add GL 80-90 Weight Gear Lube to the bottom thread of the fill

hole.

5. Reinstall the fill plug.
6. Check for leaks.

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды

Polaris Light Utility Hauler 6x6, Руководство пользователя

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды