Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 77

Страница: 77 / 116

MAINTENANCE AND LUBRICATION

Lubrication Recommendations

Oil and Filter Change

7. Place shop towels beneath

the oil filter. Using an oil

filter wrench, turn the filter

(1) counterclockwise and

remove.

8. Lubricate the gasket on the

new filter with a film of

new engine oil. Check to

make sure the gasket is in

good condition. Also make

sure the gasket from the old

filter is not still on the engine.

9. Install the new filter and tighten by hand 1/2 to 3/4 turn after

gasket contacts the engine.

10. Approximately one cup of engine oil will remain in the crankcase.

To drain, remove the drain plug on the lower right side of the

crankcase.

NOTE:

The sealing surfaces on the drain plug and

crankcase should be clean and free of burrs, nicks or scratches.

11. After draining, reinstall the drain plug.

12. Remove the dipstick (2) and add two quarts (1.9 l.) of Polaris

Premium 4 synthetic oil (see page 106). Reinstall the dipstick.

NOTE:

If the sump is not drained, add about 1 3/4 quarts initially.

13. Place the gear selector in neutral and set the parking brake.
14. Start the engine and let it idle for one to two minutes. Stop the

engine and inspect for leaks.

15. Recheck the oil level on the dipstick and add oil as necessary to

bring the level to the upper (full) mark on the dipstick.

16. Dispose of used filter and oil properly.

CAUTION

Mixing brands or using a non-recommended oil may cause serious

engine damage. We recommend the use of Polaris Premium 4 All

Season synthetic oil or API certified “SH” oil, 0-40W. Never

substitute or mix oil brands. Use only 0-40W.

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды

Polaris Light Utility Hauler 6x6, Руководство пользователя

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды