Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 51

Страница: 51 / 116

OPERATION

Hauling Cargo

Dumping Cargo

1. Select a level site to dump the cargo bed. Do not attempt to dump

or unload the vehicle while parked on an incline.

2. Set the parking brake.
3. Dismount the vehicle.
4. Pull the cargo bed release lever forward.
5. Lift the front of the cargo bed and dump the cargo.

If the weight distribution on the bed is located toward the rear of

the bed when the release lever is pulled forward, the bed may

dump on its own, which could cause serious injury. Never

operate the dump lever without checking the position of the

load. This will prevent unexpected dumping of the cargo bed.

Never carry passengers on the bed.

WARNING

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды

Polaris Light Utility Hauler 6x6, Руководство пользователя

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды