Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 68

Страница: 68 / 116

MAINTENANCE AND LUBRICATION

Periodic Maintenance Schedule

Hours of operation are based on a 10 mph average. If service is due at

20 hours, the equivalent odometer reading would be 200 miles.

Perform all services at whichever reading is reached first.

NOTE

: When inspection reveals the need for replacement parts, use

genuine Polaris parts available from your Polaris dealer.

Item

Hours or

Odometer

Frequency

Remarks

Headlamp

Pre-ride

Check operation daily; apply Polaris dielec-

tric grease to connector when replaced

Taillamp

Pre-ride

Check operation daily; apply Polaris dielec-

tric grease to socket when replaced

Tires / Air pressure

Pre-ride

Inspect daily and before each use

Brake system

Pre-ride

Inspect

Wheels

Pre-ride

Inspect

Frame nuts, bolts, fasteners

Pre-ride

Inspect; tighten when needed

Fuel and oil tanks

Pre-ride

Fill to proper level

Air box sediment tube

Daily

Inspect; drain deposits whenever visible

Air filter (pre-cleaner)

Daily

Inspect and clean

Coolant level

Daily

Replace engine coolant every two years

Air Filter (main element)

Weekly

Inspect; replace if necessary

Brake pads

10 hrs/100

miles

Monthly

Inspect for wear periodically

Breather filter

20 hrs

Monthly

Inspect; replace annually and as needed

Battery

20 hrs

Monthly

Inspect and clean terminals; check fluid level

Transmission oil level

25 hrs

Monthly

Inspect monthly; change annually

General lubrication

50 hrs

3 months

Lubricate all fittings, pivots, cables, etc.

Throttle cable / ETC switch

50 hrs

6 months

Inspect before each use; adjust, lubricate,

replace if necessary

Choke (enricher) cable

50 hrs

6 months

Inspect; adjust, lubricate, replace if neces-

sary

Carburetor float bowl

50 hrs

6 months

Drain bowl periodically and prior to storage

More often under severe use, such as dirty or wet conditions

Dealer service item

Improperly performing the procedures marked with a

could

result in component failure and lead to serious injury or death.

Have an authorized Polaris dealer perform these services.

WARNING

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды

Polaris Light Utility Hauler 6x6, Руководство пользователя

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды