Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 46

background image

HGF Series Service Procedure

34

Figure 98

Figure 97

Figure 96

Figure 95

Install dirt and water
seal

44. Apply a small amount of clean

grease on the lip of the seal (39).
Install the seal onto the jacket
tube and input shaft/wheel tube.
See FIGURE 96.

Make final assembly
check and remove unit
from fixture

45. Make final check of the relative

groove positions on the side of the
unit using the component
alignment groove graphic on page
9B (fold-out) for comparison.
Disassemble and correct any
misassembly. Remove the four
nuts holding the unit to the fixture
and remove the unit. Make sure
shaft rotates by hand. See
FIGURE 97.

Assemble contact
brush and related parts

46. Place HGF unit on a clean

working surface. If required,
assemble spacer (51) [for 1 1/2
inch (38 mm) jacket tube only],
contact brush assembly (44)
washer (46) [for 1 3/4 inch (44
mm) jacket only] and screw and
lock washers (45). See FIGURES
98, 99, and 100. Check for the
required electrical continuity
(connection) from the horn cable
assembly (47) upper terminal to
the contact brush (44) terminal as
the input shaft/wheel tube is
rotated. There must not be any
electrical continuity (connection)
from the upper horn cable terminal
or contact brush terminal to any
other exposed part of the HGF
unit, including the body of the
contact brush.

«
...
39
40
41
42
43
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: OMCA Страницы: 72

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: jcb Страницы: 41

Бренд: Conductix-Wampfler Страницы: 12

Flumen OPTI-TR 22

Бренд: Wilo Страницы: 88

Circaid Juxtafit Essentials

Бренд: medi Страницы: 2

Inocoat Inocenter

Бренд: Sames Страницы: 58

Perma-Tork HB6-1

Бренд: Magpowr Страницы: 4

Бренд: CNC Страницы: 21

Бренд: Jäger Страницы: 40

Бренд: vacuubrand Страницы: 48

Бренд: Otto Bock Страницы: 104

Live Mix Pro 40-8

Бренд: DAPAudio Страницы: 43

Бренд: istobal Страницы: 58

Бренд: Abilica Страницы: 24

Бренд: C.B.S. SCIENTIFIC Страницы: 16

Бренд: M-Audio Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды