Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 46

background image

23

HGF Series Service Procedure

Figure 55

Figure 54

Figure 53

Figure 52

If input shaft/wheel tube (33) is 7/8
inch (22 mm) diameter on the hand
wheel end or has a contact ring
assembly (43), slide the retainer plate
(36) then the washer (35) onto the
retaining ring groove end of the input
shaft/wheel tube, past the ring
groove. The recessed face of the
retaining plate must be toward the
washer. See FIGURE 52.

Install retaining ring

6.

Apply small amount of grease to
the recessed face of retainer plate
(36) and to washer (35). If the
input shaft/wheel tube (33) is 3/4
inch (19 mm) diameter with no
contact ring assembly (43), place
the retainer plate into the upper
cover and jacket assembly (37)
with recessed retainer face out.
Place washer (35) against
recessed face of retainer plate.

Install retaining plate
and washer

7.

Install retaining ring (34) onto input
shaft/wheel tube (33) using the
appropriate external retaining ring
pliers. See FIGURE 53.

Install retaining ring

8.

Slide input shaft/wheel tube (33)
assembly into upper cover end of
upper cover and jacket tube
assembly (37) and through the
bushing (38) until the retaining ring
(34) bottoms against washer (35)
which bottoms against retainer
plate's (36) recessed face and the
retainer plate seats against the
end of jacket tube. See FIGURES
54 & 55.

Install input shaft/wheel
tube

9.

Assemble the upper cover plate
(32) over the four bolts (40) and
input shaft/wheel tube (33) onto
the upper cover and jacket tube
assembly (37) with the highly
polished surface up and the edge
with the alignment groove in the
same position relative to the jacket
tube contact brush cover hole as
noted before disassembly. See
FIGURE 55. (Reference
alignment groove graphic--fold-out
page.)

Install upper cover plate

«
...
28
29
30
31
32
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: Latchways Страницы: 80

Бренд: Kapriol Страницы: 28

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Dynapro ET 355 Monitor HL

Бренд: 3M Страницы: 23

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: IEMCA Страницы: 82

KID 80-IV Touch

Бренд: IEMCA Страницы: 122

Бренд: Calrec Страницы: 92

Бренд: Labnet Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды