Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 46

background image

15

HGF Series Service Procedure

Figure 25

Figure 24

Figure 23

Figure 22

27. Remove and discard the

commutator seal (19) from the
commutator cover (20). See
FIGURE 22.

Remove commutator
seal

28. Remove the eleven hex.

socket head screws (18), that
hold the metering package
together. See FIGURE 23.
Use a 3/32 inch Allen wrench.
Inspect screws for thread and
socket damage and replace as
required.

Remove cap screws

29. Lift the commutator cover (20)

from the metering package.

Remove commutator
cover

30. Inspect the ground surfaces of

the commutator cover (20).
You should notice a "normal"
polished pattern due to the
rotation of the commutator
(22). If the cover has nicks,
burrs, or scoring, it must be
replaced. See FIGURE 24.

Inspect commutator
cover

31. Remove commutator ring (21).

See FIGURE 25. Inspect for
cracks, burrs, and scoring.

Remove commutator
ring

CAUTION: Handle commutator
ring with care, as it is easily
broken.

CAUTION

«
...
20
21
22
23
24
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: MacDon Страницы: 84

Бренд: MacDon Страницы: 89

Бренд: Patton electronics Страницы: 18

Бренд: Keithley Страницы: 32

Бренд: jcb Страницы: 166

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: NAD Страницы: 10

Бренд: SAMCHULLY Страницы: 48

Бренд: QBC Diagnostics Страницы: 65

Бренд: PANDROL Страницы: 36

Бренд: fadini Страницы: 20

Aspect Q-CARD 100-4T

Бренд: idi Страницы: 38

SC 2 Deluxe EasyFix

Бренд: Kärcher Страницы: 12

Бренд: Kärcher Страницы: 16

Бренд: Raymarine Страницы: 3

SmartPilot ST8002

Бренд: Raymarine Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды