Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 46

background image

18

HGF Series Service Procedure

Figure 36

Figure 35

Figure 34

Figure 33

41. Note position of bearing spacer

undercut (groove-side down).
Remove thrust bearing (28) and
bearing spacer (27) from upper cover
plate (32). See FIGURE 33.

Remove thrust bearing
& spacer

42. Inspect the thrust bearing (28)

for brinelling (dents) or spalling
(flaking), if either exists, or if
one of more of the rolls is lost
or broken, replace the bearing
assembly. See FIGURE 33.
Replace seal spacer (31) or
bearing spacer (27) if worn or
broken.

Inspect bearing and
spacers

CAUTION: The thrust bearing
assembly (28) will have 16 or 17 rolls
evenly spaced in a roller cage that
can hold 32 or 34 rolls or the thrust
bearing will have a full complement
of 32 or 34 rolls. The bearing
assembly with 32 or 34 rolls should
not be replaced with a bearing
assembly that has 16 or 17 rolls.

CAUTION

NOTE: For reassembly purposes,
note the radial position of the
alignment grooved edge of the upper
cover plate (32) relative to the jacket
tube contact brush hole if the unit is
so equipped.

NOTE

43. Remove the upper cover plate (32)

(four plates bonded together). Inspect
the upper cover plate. You should
notice some polishing due to the
action of the seal. The plate should
be free of brinnelling (dents) or
spalling (flaking). If it is damaged, the
upper cover plate must be replaced.
See FIGURE 34.

Remove and inspect
upper cover plate

CAUTION: Protect seal area.

CAUTION

44. Slide the seal (39) from the

jacket tube. If the seal is worn
or damaged, it must be
replaced. See FIGURE 35.

Remove dirt and water
seal

45. Remove the input shaft/wheel

tube (33) assembly, sliding it
out of the upper cover end of
the assembly. See FIGURE 36.

Remove input
shaft/wheel tube

NOTE: If the input shaft/wheel
tube assembly has 7/8
serrations or contact ring
assembly (43), the washer (35)
and retaining plate (36) will be
removed with input shaft/wheel
tube assembly.

NOTE

«
...
23
24
25
26
27
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: FagronLab Страницы: 16

Бренд: Panlux Страницы: 2

Бренд: PacBio Страницы: 13

Бренд: Pablo Страницы: 4

Бренд: PA Страницы: 28

Бренд: Hach Страницы: 456

LUXOMAT net PBM-KNX-DX-4W

Бренд: B.E.G. Страницы: 16

Бренд: Guyatone Страницы: 2

PRO-FORM ab GLIDER

Бренд: ICON Health & Fitness Страницы: 16

Бренд: Woods Страницы: 54

Бренд: Bodyworx Страницы: 17

Бренд: Wood-mizer Страницы: 59

Бренд: Tandem Страницы: 7

Бренд: Baileigh Industrial Страницы: 40

Tidland Performance Series

Бренд: Maxcess Страницы: 72

Бренд: Tadano Страницы: 16

Бренд: Ibiza Страницы: 32

ChemiDoc XRS 170-8070

Бренд: BIO RAD Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды