Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 46

Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 23

16

HGF Series Service Procedure

Figure 28

Figure 27

Figure 26

32. Remove the commutator (22)

from the rotor (24). See
FIGURE 26.

Remove commutator

CAUTION: Five alignment pins (11)
connect the commutator to the
rotor with a slip fit. Care and
minimum force should be used to
separate the two components.

CAUTION

33. Remove the five alignment

pins (11). See FIGURE 27.

Remove alignment pins

34. Remove drive link spacer (23).

See FIGURE 28. Replace it, if
it is grooved or worn.

Remove & inspect drive
link spacer

35. The commutator (22) is made

up of two round plates pinned
and bonded together as a
permanent assembly and is
not subject to further
disassembly. Inspect the
ground surfaces of the
commutator. The holes and
edges should be free of nicks.
The ground surfaces should be
free of scoring. The edges
should be sharp.

Inspect commutator

NOTE: The commutator (22)
and commutator ring (21) are a
matched set. If either is worn
or damaged, you must replace
the set.

NOTE

36. With the rotor set (24, 25) lying

on the drive plate (26), the
rotor (24) should rotate and
orbit freely within the stator
(25). The commutator side of
the stator face must be free of
grooves or scoring.

Inspect rotor set

NOTE: The rotor (24) and
stator (25) are a matched set.
You must replace them as a
matched set, if either is worn
or damaged.

NOTE

«
...
21
22
23
24
25
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов