Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 46

Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 19

12

HGF Series Service Procedure

Figure 13

Figure 12

Figure 11

Figure 10

11. Inspect the ground surfaces of

the port manifold (8). You
should notice a "normal"
polished pattern due to the
rotation of the valve plate (13)
and hex drive assembly (10).
All edges should be sharp and
free of nicks and burrs. The
surfaces of the port manifold
should be free of scratches or
scoring. If any of these wear
conditions exist, replace the
port manifold.

Inspect port
manifold

CAUTION: Many components
in the unit have finely ground
surfaces. Be careful not to
nick or scratch these surfaces.

CAUTION

12. Remove the valve ring (12),

discard the two seal rings (3).
See FIGURES 10 and 11. The
valve ring should be free of
nicks and scoring.

Remove valve ring

13. Remove the valve plate (13) by

lifting it from the isolation
manifold (15).

Remove valve plate

14. Inspect the slot edges and

ground surfaces. If the valve
plate (13) shows nicks or
scoring or the edges are not
sharp, it must be replaced.
See FIGURE 12.

Inspect valve plate

NOTE: The valve ring (12)
and valve plate (13) are a
matched set and must be
replaced as a set.

NOTE

15. Remove three springs (14)

from the isolation manifold (15)
pockets. See FIGURE 13.

Remove springs

NOTE: The unit has two
different length spring sets.
The set you have just removed
from the isolation manifold is
one-half inch (13 mm) long.
Keep this spring set separate
from the set removed from the
port manifold (8).

NOTE

«
...
17
18
19
20
21
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов