Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 46

background image

19

HGF Series Service Procedure

Figure 40

Figure 39

Figure 38

Figure 37

46. Inspect the input shaft/wheel tube

(33) and sub-assembly
components as assembled.
Inspect input shaft/wheel tube for
worn or damaged serrations,
wheel nut threads, bearing
diameter, and flats on the lower
end. Inspect the other
components of the sub-assembly
for wear damage. If the sub-
assembly includes horn cable
assembly(ies), check its electrical
functions with an appropriate
continuity checking device. If this
sub-assembly passes inspection,
set it aside, and go to disassembly
procedure number 50. If it does
not pass inspection, continue with
disassembly procedure number
47.

Inspect input
shaft/wheel tube sub-
assembly

NOTE: There must be electrical
continuity (connection) from the upper
terminal of horn cable assembly (47)
to the contact ring of the contact ring
assembly (43). There must not be any
electrical continuity (connection) from
horn cable assembly terminal or
contact ring assembly to the input
shaft/wheel tube (33) or other
components.

NOTE

47. Using appropriate external

retaining ring pliers, remove the
retaining ring (34) from the input
shaft/wheel tube (33). See
FIGURE 37. Discard, if deformed
or broken.

Remove retaining ring

48. Remove washer (35) and retaining

plate (36) from input shaft/wheel
tube (33) or upper cover and jacket
assembly (37). Discard, if
deformed or damaged. See
FIGURE 38.

Remove retaining plate

NOTE: Retaining plate (36) cannot be
serviced separately, but is a part of an
upper cover and jacket tube assembly
service kit.

NOTE

49. Remove tape, horn cable

assembly (47), screw (42), and
contact ring assembly (43)
from input shaft/wheel tube
(33) if the unit is so equipped.
Replace broken or electrically
defective components. See
FIGURES 39 and 40.

Remove horn cable and
contact ring assemblies

«
...
24
25
26
27
28
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: Parker Страницы: 54

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: Raymarine Страницы: 90

Бренд: Federal Signal Corporation Страницы: 12

Бренд: GE Страницы: 212

Бренд: Quivogne Страницы: 13

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренд: Vaillant Страницы: 76

Бренд: H2flow Страницы: 2

Бренд: V-TAC Страницы: 27

Бренд: Yacht Sentinel Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды