Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 13

Страница: 13 / 46

HGF Ser

ies Ser

vice Procedure

HGF Exploded Assembly View-Typical

Item Number

Description

Nut 5/16 UNF 24 (4)

Port Cover

Seal Ring (5)

Seal Ring (White)

O’Ring (3), (4) or (5)

Ball-7/32 inch (6mm) dia.

Relief valve cartridge

Coil spring

Plug

Hex plug

O’Ring, Plug & O’Ring assy.

O’Ring

Port Manifold

Spring, 3/4 inch (19mm) (3)

Hex Drive assy.

Alignment Pin (Needle Brg.) (9)

Valve Ring

Valve Plate

Spring, 1/2 inch (13mm) (3)

Isolation Manifold

Drive Link

Metering Ring

Screw, Hex Socket Hd (11)

Seal, Commutator

Commutator Cover

Commutator Ring

Commutator

Spacer–Drive Link

Rotor

Stator

Drive Plate

Spacer–Thrust Bearing

Thrust Bearing

Face Seal

Seal Spacer

Upper Cover Plate

Input Shaft/Wheel Tube

Retaining Ring

Washer–Retaining Plate

Retaining Plate

Upper Cover & Jacket Assy.

Bushing

Seal

Special Bolt, 5/16 24UNF-2A

Nut

Screw

Contact Ring Assy.

Contact Brush Assy.

Screw & Lock Washer

Washer [for 1-3/4 inch (45mm)

Jacket]
47

Horn Wire Cable Assy.

Spacer [for 1-1/2 inch (38 mm)

Jacket]
52

Ball 9/32 inch (22mm)

Items # 44, 45,46, 51 are not part of HGF service
assembly unit. They must be purchased as
separate items of order.

Matched Set

}

Matched Set

Rotor Assy–

Matched Set

Содержание Hydraguide HGF Series















































Результаты поиска

Содержание Hydraguide HGF Series

Отзывы:

Parker Hydraulics Hydraguide HGF Series, Процедура обслуживания, Страница: 13 / 46

Результаты поиска

Содержание Hydraguide HGF Series

Отзывы: