Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 46

background image

HGF Series Service Procedure

WARNINGS for Proper Steering System Operation

WARNING: DO NOT WELD, BRAZE, OR SOLDER ANY STEERING SYSTEM COMPONENT.

WARNING: MAXIMUM OPERATING PRESSURE MUST NOT EXCEED VEHICLE MANUFACTURER'S
RECOMMENDED PUMP PRESSURE CAPACITY.

WARNING: ALWAYS CAREFULLY INSPECT ANY STEERING SYSTEM COMPONENT THAT MAY HAVE
BEEN STRUCK OR DAMAGED DURING OPERATION OR IN AN ACCIDENT. REPLACE ANY COMPONENT
THAT IS DAMAGED OR THAT IS QUESTIONABLE.

37

Tips for Maintaining the Hydrostatic Steering System

Top up fluid level in reservoir as necessary.

Maintain correctly inflated tires.

Always use a puller to remove the steering wheel. Do not use a hammer, torch, or crow bar.

Investigate and correct immediately any play, rattle, shimmy, or other unusual occurrence in
the steering system.

Remove cause of steering column misalignment.

Encourage all drivers or operators to report any malfunction or accident that may have
damaged a steering system part.

Do not attempt to weld any broken steering component. Replace the component with original
equipment only.

Do not cold straighten, hot straighten, or bend any steering part.

Prevent dirt or other foreign matter from entering the hydraulic system. Clean off around filler
caps before checking oil level.

Investigate and correct any external leak in the steering system, no matter how minor the leak.

Comply with manufacturer's specifications for cleaning or replacing the filter.

Ross extends close technical cooperation and assistance. If steering problems occur which you cannot solve, please
contact our Ross Field Service Department. Our phone number and address are on the back cover of this manual

«
...
42
43
44
45
46
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: NAD Страницы: 10

Бренд: JB Systems Страницы: 12

Бренд: Fisher Scientific Страницы: 42

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренд: Tar River Страницы: 61

Бренд: Baileigh Industrial Страницы: 12

Бренд: Qtx Страницы: 6

WELCH LVS 600 T

Бренд: Gardner Denver Страницы: 68

Бренд: Kellfri Страницы: 44

Бренд: Hoist Fitness Страницы: 17

Бренд: Peak Pilates Страницы: 4

Бренд: Cablexpert Страницы: 12

Бренд: Reflex Marine Страницы: 36

Thermo Therapy TT-202

Бренд: Whitehall Страницы: 12

Бренд: TECshow Страницы: 22

Бренд: Zen Pro Страницы: 40

Бренд: E2S Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды