Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 46

background image

11

HGF Series Service Procedure

Figure 8A

Figure 9

Figure 8

Figure 7

NOTE: The unit has two different
length spring sets. The set you have
just removed from the port manifold
are three-quarter inch (19 mm) long.
Keep this set of three springs
separate from the next set of three
springs to be removed.

10. Inspect the springs for bent or

distorted coils. If a spring is
broken or deformed, all six springs
in the unit should be replaced.

5.

Grasp the port cover (2)
assembly and lift it from the
unit. Discard three, four, or
five seal rings (4) and seal ring
(3) or if included white seal

ring (3A). See FIGURE 7.

Remove loose check ball (52)
from top of port manifold (8) if
included.

Remove port cover

6.

If included, remove the
loosened plug (6) and o-ring
(7) assembly from the port
cover. Be ready to catch the
steel check ball (5) as it falls
from its cavity. Discard o-ring
(7). See FIGURE 8.

Remove plug

6A. If included, removed the

loosened hex plug (6A) and o-
ring (7A) from the port cover
(2). Discard o-ring. Remove
relief valve cartridge (5A) and
spring (5B) assembly. A bent
or lost spring (5B) can be
serviced separately. See
FIGURE 8A. Do not try to
disassemble relief valve
cartridge (5A).

Remove hex cap &
relief valve cartridge &
spring assy.

Inspect port cover

7.

Inspect the port cover (2) for
port fitting sealing surface
scratches and thread damage.
Replace port cover, if these
conditions are evident.

NOTE

8.

Carefully lift the port manifold
(8) (3 plates bonded together)
from the unit. See FIGURE 9.

Remove springs

NOTE: Be prepared to catch
three springs (9) which may
become disengaged when
removing the port manifold.

NOTE

Remove port manifold

9.

Remove three springs (9) from
the port manifold (8).

Inspect springs

«
...
16
17
18
19
20
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: M-system Страницы: 3

Бренд: M-system Страницы: 5

Бренд: MA Страницы: 2

Бренд: VDO Страницы: 15

Бренд: VDO Страницы: 20

Бренд: M-Audio Страницы: 3

Бренд: Xtralis Страницы: 26

Wallach UltraFreeze

Бренд: Cooper Surgical Страницы: 4

Smartzone PViQ Connectivity System

Бренд: Panduit Страницы: 179

Бренд: ALLEN & HEATH Страницы: 6

Impression FR10 Bar

Бренд: GLP Страницы: 65

Pivot track filler

Бренд: Norwest Страницы: 16

Бренд: ResMed Страницы: 9

Бренд: Major tech Страницы: 20

Бренд: Laserworld Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды