background image

22

HGF Series Service Procedure

Figure 51

Figure 50

Figure 49

NOTE: If contact ring assemblies 
and horn wires are not required, 
go to assembly Step 6.

NOTE

4.

Install the contact ring 
assembly(ies) (43), if required, 
onto the input shaft/wheel tube 
(33) into the same position as 
before disassembly. See FIGURE 
50.

Install contact ring
assembly

CAUTION: Failure to check the electrical
functions of the input shaft/wheel tube,
horn cable assembly before it is
assembled into the HGF unit, would
require another complete disassembly
of the unit if proved electrically defective
after the HGF unit is assembled.

CAUTION

5.

Insert horn cable assembly (47) 
spade terminal end first into the 
steering wheel end of the input 
shaft/wheel tube (33) so that it 
exits from the horn cable outlet 
hole. Push the horn cable spade 
terminal onto the contact ring (43) 
terminal connector. Be sure it is a 
good, firm connection. Position 
the horn cable protector sleeve so 
that it protects the horn cable from 
any sharp corner where it exits the 
horn cable outlet hole. Position 
and fasten the contact ring 
assembly (43) with screw (42).
Use about 1 1/2 turns of tape 
around the input shaft/wheel tube, 
horn cable and contact ring to hold 
the horn cable in place. See 
FIGURE 51. Check for electrical 
continuity (connection) required 
from horn cable assembly (47) 
upper terminal to contact ring of 
contact ring assembly (43). There 
must not be electrical continuity 
(connection) from upper horn 
cable terminal or contact ring to 
input shaft/wheel tube (33). Also, 
see FIGURES 99 and 100.

Install horn cable
assembly

3.

Apply clean grease to bushing (38) 
and stack upper cover and jacket 
tube assembly (37) on the four 
bolts (40) with the jacket tube 
pointing down through the hole in 
the fixture. Make sure the square 
shoulder of the bolts engage the 
square holes in the upper cover.
See FIGURE 49.

Stack upper cover and
jacket tube assembly

Содержание Hydraguide HGF Series















































Отзывы: