Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 46

background image

HGF Series Service Procedure

35

THIS COMPLETES THE ASSEMBLY OF HGF UNIT WITH THE
EXCEPTION OF WHEEL NUT (41), CONTACT BRUSH COVER
SEAL (48), CONTACT BRUSH COVER (49), AND RELATED
SCREW AND LOCK WASHERS (50) WHICH MUST AWAIT
INSTALLATION OF STEERING WHEEL AND ELECTRICAL
SOURCE CONNECTION. REF. FIGURES 99 AND 100.

CAUTION: IF THE INSTALLATION APPLICATION HAS A
JACKET TUBE (COLUMN) SUPPORT CLAMP, IT IS
EXTREMELY IMPORTANT THAT THE UPPER COVER AND
JACKET TUBE ASSEMBLY ALIGN WITH THIS CLAMP IN THE
FREE STATE. IF MISALIGNMENT IS EVIDENT, THE HGF
UNIT MUST BE SHIMMED AT THE MOUNTING SURFACE TO
ELIMINATE THIS MISALIGNMENT, OR DAMAGE TO THE HGF
UNIT MAY RESULT.

Figure 99

TYPICAL

7/8" (22 mm) Input Shaft/Wheel Tube

1 1/2" (38 mm) Jacket Tube

New Horn Contact Design

7/8” (22 mm) Input Shaft/Wheel Tube

1 1/2” (38 mm) Jacket Tube

«
...
40
41
42
43
44
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: UFO Страницы: 16

Бренд: Fayat Group Страницы: 50

Бренд: Halyard Страницы: 88

Бренд: Haag-Streit Страницы: 18

Бренд: Haag-Streit Страницы: 20

Бренд: V-TEK Страницы: 2

Бренд: V-TEK Страницы: 112

Бренд: Lalizas Страницы: 12

BOBCAT 130 Series

Бренд: Balcrank Страницы: 12

INTRAmatic 31 ES

Бренд: KaVo Страницы: 52

Бренд: Numark Страницы: 11

Бренд: Daihan Scientific Страницы: 27

WEEDDEVIL ST-97

Бренд: R+M Suttner Страницы: 16

Бренд: Viking Страницы: 6

Бренд: U.S.SAWS Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды