Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 46

background image

20

HGF Series Service Procedure

Figure 44

Figure 43

Figure 42

Figure 41

50. Remove the upper cover and jacket

tube assembly (37) and lay the
assembly on the bench. See FIGURE
41.

Remove upper cover
and jacket tube
assembly

51. The jacket tube has been pressed into

and welded to the upper cover plate
support tube such that the retainer
plate (36) is flush with the upper cover
plate surface when seated against the
jacket tube. Any signs of looseness or
movement of jacket tube in the upper
cover support tube will require
replacement of upper cover and jacket
tube assembly (37), retainer plate (36)
and bushing (38) as a set. A loose or
worn input shaft/wheel tube bushing
(38) in the upper cover and jacket tube
assembly can be serviced separately.

Inspect upper cover
and jacket tube
assembly

52. If the bushing (38) is to be replaced,

place the upper cover and jacket tube
assembly (37) in a vise with the vise
jaws clamping firmly on the jacket
tube without deforming the jacket
tube. Using an appropriate type of
pliers, "uncrimp" or relieve the two
crimped areas on the bushing end of
the jacket tube. Remove the bushing
using a bearing or seal type puller and
discard the bushing. Set the upper
cover and jacket tube aside to await
assembly. See FIGURES 42, 43.

Remove worn bushing

53. Remove the nuts holding the four

bolts (40) to the fixtures and remove
the bolts. Bolts with the square
shoulder or the threads damaged
such that the nuts cannot be properly
torqued must be replaced. See
FIGURE 44.

Remove and inspect
bolts

WARNING: USE ONLY GENUINE
OEM APPROVED REPLACEMENT
PARTS. THE USE OF IMPROPER
PARTS COULD CAUSE A LOSS OF
STEERING WHICH COULD LEAD TO
AN ACCIDENT.

The HGF disassembly is complete.

WARNING

NOTE: The relative positioning of the
contact ring(s) (43) should be noted
before removal for reassembly
purposes.

NOTE

«
...
25
26
27
28
29
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: ACS Страницы: 56

Бренд: ZOLL Страницы: 84

Бренд: Kaivac Страницы: 29

Бренд: MacDon Страницы: 65

Бренд: Baker Instrument Company Страницы: 24

Бренд: Taylor Страницы: 70

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: J.P. SELECTA Страницы: 32

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды