Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 46

background image

The model HGF Hydraguide™ power steering unit is Ross' most recent addition to its series of hydrostatic

steering products. The HGF combines several advanced features designed to meet industry's needs for improved
steering of its construction, industrial, and agricultural vehicles.

• An ultra compact and light weight package designed for easy installation with fluid connections at the lower end of
unit.
• An open center fast response rotary plate type valve (spring centered) with options of open or closed cylinder ports
and "power beyond".
• Small eccentric rotor set provides smooth operation.
• Lower optional noise levels.
• Column (jacket tube) and input shaft/wheel tube integral to unit for improved column/unit alignment. Lengths tailored
to user requirements.

For operation, the HGF system requires the following components:

• an engine-driven pump,
• a relief valve,
• a cylinder or cylinders,
• a reservoir and filter,
• suitable fluid lines or hoses, and
• the HGF hydrostatic unit.

The driver has power steering control at all times, so long as system components work together, system integrity

is maintained, and adequate fluid is present. If there is a failure in the high-pressure circuit, a loss of power steering
will result. The HGF, however, is designed to have some manual steering capability, depending on the installation. If
you can't manually steer the vehicle without using extraordinary measures, such as leaving your seat, or pushing with
your legs, don't try it. Some vehicles may be impossible to steer manually because of their weight and size. Repair
the failure in the power circuit.

HGF Design Features

Hydraguide

™

WARNING: SUCH EXTRAORDINARY MEASURES SHOULD NOT BE USED IN ATTEMPTING TO MANUALLY
STEER THE VEHICLE, AS THEY MAY GENERATE FORCES IN EXCESS OF 125 FT. LBS. (169 N m),
THEREBY DAMAGING THE UNIT INTERNALLY, WHICH COULD RESULT IN A COMPLETE LOSS OF
STEERING.

i

«
1
2
3
4
5
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: Datavideo Страницы: 50

Бренд: Waterous Страницы: 90

Бренд: Campbell Страницы: 14

Бренд: A.MENARINI Страницы: 2

Бренд: B-K lighting Страницы: 3

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: Nitecore Страницы: 4

Бренд: M-Audio Страницы: 3

Бренд: Xtralis Страницы: 26

Бренд: 3nStar Страницы: 14

Бренд: Eaton Страницы: 2

INTRA PROPHYwiz 181 P

Бренд: KaVo Страницы: 22

Бренд: Festo Страницы: 40

Бренд: Neurotech Страницы: 24

Бренд: Focal Meditech Страницы: 10

Бренд: Rohm Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды