Parker Hydraulics Hydraguide HGF Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 46

background image

6

HGF Series Service Procedure

Troubleshooting Checklists

1. NOISE

NORMAL NOISE
A low hissing from the HGF control valve section during a turn
A noise from the system relief valve when it is actuated
Pump growl from some types of power steering pumps

ABNORMAL NOISE
A squealing noise during a turn may indicate that the belt or belts should be tightened or replaced
A clicking noise during a turn may indicate that some component is loose and shifting under load.

II. POSSIBLE STEERING PROBLEMS AND CAUSES

STEERING WANDER
Different size tires
Tire pressure incorrect or unequal left to right
Loose or worn steering linkage parts
Improperly adjusted or worn wheel bearings
In some vehicles, front end out of alignment

NO RECOVERY FOR OPEN-CYLINDER UNIT
Tire pressure low
Steering linkage parts binding
Tight front axle kingpins
Steering column binding or misaligned

SHIMMY
Improperly mounted tire or wheel
Components in steering linkage loose, worn, or out of adjustment
Wheels or brake drums out of balance
Wheel bearings improperly adjusted
Air in the hydraulic system

HIGH STEERING EFFORT IN ONE DIRECTION
Vehicle overloaded
Low hydraulic system pressure
Excessive system heat causing HGF plate valve to stick. See checklist under Excessive Heat.

«
...
8
9
10
11
12
...
»

Содержание Hydraguide HGF Series















































Отзывы:

Нет отзывов

Похожие инструкции для Hydraguide HGF Series

Бренд: Obdstar Страницы: 10

Бренд: Panasonic Страницы: 30

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

APT-9411 Series

Бренд: TAKAYA Страницы: 77

Бренд: Tadano Страницы: 402

Бренд: XFit Страницы: 16

BlackBox Series

Бренд: Nakamichi Страницы: 23

Бренд: Harken Страницы: 4

Бренд: A&D Страницы: 33

Бренд: K-SPORT Страницы: 5

MIDORI ULB-50sc

Бренд: Ushio Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды