Opel 1900 1973 Скачать руководство пользователя страница 55

Страница: 55 / 625

34 1973 OPEL SERVICE MANUAL

one direction, but should not light at all in the otlier

direction. Diodes in each set of three should
current and block current in the ‘same directions
the others in the set. See Figure

Removing Diodes

Positive Diodes

1. Press defective diode out of diode support, back-

ing-up support with a sleeve

larger than

diode and pushing diode through with a shaft
slightly smaller than diode. See Figure

Figure 1 D-22 Removing Diode

Negative Diodes

1. Clip lead from defective diode. Clip lead close

enough to diode so that tool will

properly.

Figure 1

Removing Diode

2. Using Tool J-23526, press diode from support. See
Figure

Installing Diodes

Positive Diodes

1. Press new diode into diode support. See Figure

Figure

Installing Diode

Negative Diodes

1. Using Tool J-23526, press diode into support. See

Figure

Insert negative diode pigtail lead

through tool pilot.

Alternator Reassembly

1. Clean and inspect all parts. Check brushes. Re-

place them if they have worn

down to

inch.

2. Lubricate both bearings with special ball bearing
lubricant.

3. Press rear bearing on rotor shaft and install front

bearing into drive end frame.

4. Assemble

together with windings into rear

end frame.

5. Install both diode supports.

6. Solder diode connections and ends of

wind-

ings together. Since diodes are very sensitive to heat,
solder quickly using a very hot soldering iron.

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды

Opel 1900 1973, Руководство по обслуживанию

Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды