Opel 1900 1973 Скачать руководство пользователя

Страница: 300 / 625

ENGINE MECHANICAL AND MOUNTS

The engine

does not rest on

the front suspension

cross member as in the Opel

and Manta but on

a separate cross member. On removal and installa-
tion of the engine the front suspension cross member

need not be detached.

Fig.

Right Front Engine Suspension with Cross

Member

1. Disconnect battery negative cable,

2. Remove air cleaner.

3. Drain radiator coolant by disconnecting lower
radiator hose. Disconnect upper radiator hose. See
Figure

Radiator need not be disconnected.

4. Disconnect all electrical connections:

a. Coil wire to distributor.

Wires from alternator. Remove unit and bracket.

Battery positive cable at starter switch.

d. Oil pressure switch wires at cylinder block.

e. Wires from starter solenoid.

5. Remove vacuum hoses at tee mounted to intake
manifold. Remove tee from manifold to avoid inter-
ference during engine lowering.

6. Remove throttle linkage and carburetor.

7. Disconnect heater hoses.

8. Disconnect water valve bracket to manifold,

9. Remove gear shift lever.

10. Using suitable equipment lift up engine so that

front engine mounts are somewhat relieved.

Figure

Radiator Hose Clamp Location

11. Raise vehicle, both front and rear end. A two post

axle type hoist recommended for this operation.

12. Disconnect fuel line at fuel pump and plug. Be

sure fuel line is disconnected from any engine and
transmission clips.

13. Disconnect speedometer cable from transmis-

sion.

14. Disconnect clutch cable.

15. Disconnect drive shaft at rear universal joint and

remove.

16. Disconnect exhaust at manifold.

17. Remove tailpipe and

hangers.

18. Remove ground strap from engine to side rail.

19. Detach transmission cross member from trans-

mission and frame. See Figure

Detach engine cross member from engine and

frame.

21. Carefully lower engine

and

transmission and

remove from underneath vehicle.

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды

Opel 1900 1973, Руководство по обслуживанию

Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды