manualshive.com logo in svg

Opel 1900 1973, Руководство по обслуживанию, Страница: 558 / 625

Поделиться
Скачать
Opel 1900 1973 Скачать руководство пользователя страница 558

 COMPONENTS ALL MODELS

Figure 

 Sheet Metal Cover Removed

5. Unplug compressor clutch electrical plug, and

remove idler pulley bracket assembly and ground
wire. See Figure 

 1. Radiator hose is removed for

photographic reasons only.

 

 Location of Compressor Mounting

,

Support Bolts Opel 1900 Manta

Figure 

 1 Location of Idler Pulley, Bracket and

Ground Wire Opel 1900   Manta

6. After system is completely discharged, remove

refrigerant hoses from compressor adapter fitting

and cap hoses and adapter fitting to keep contami-
nants from entering.

7. Support compressor from underneath and

remove three (3) compressor mounting support bolts
and support bracket. Carefully lower compressor.
See Figure 

 52. During removal, maintain the

compressor position so that the sump is downward.

Do not rotate compressor shaft.

 Support compressor from underneath and install

into position from 

under 

car. Insure that compressor

 

 oil charge.

2, Install three (3) compressor mounting support

bolts. See Figure 

 Install compressor support bracket. Torque bolts

to 

 

 See Figure 

 Install idler pulley fan belt, bracket assembly

 ground wire. Plug   compressor clutch electri-

cal! plug. See Figure 

 Install refrigerant hoses and evacuate system.

Refer to EVACUATING THE. SYSTEM.

 While system is being evacuated install sheet

 cover. See Figure 

 Install air cleaner and heat pipe.

 Install negative battery cable and charge system.

 CHARGING THE SYSTEM.

REMOVAL AND INSTALLATION OF

   OPEL 1900 MANTA

I

1.’ Discharge system. Refer to DISCHARGING

THE SYSTEM.

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов