Opel 1900 1973 Скачать руководство пользователя страница 51

Страница: 51 / 625

1 D- 30

1973 OPEL SERVICE MANUAL

6. Make sure all electrical accessories are turned

Start engine with battery post adapter switch closed;
open switch as soon as engine started.

7. Adjust engine speed to 2500 RPM.

8. Turn tester control knob to “LOAD” position

adjust knob to obtain highest possible ammeter r&d-
ing. Output must be 30 amperes minimum. If
is okay, proceed to voltage regulator test below.

9. If output is low, defect may

in alternator or

regulator. To eliminate regulator, supply

rent direct to cause full

output. Unplug

three-way connector from regulator and plug in a

jumper between the red and black leads. See Figure

Retest as described in Steps 7 and 8. If output

is still low, generator is faulty and must be

Figure

Alternator

Check

10. If output (using field jumper) is now okay, defect

is in the regulator or wiring harness. Check all wiring
connections. If all wiring is okay, try

regulator; if output now tests okay (without
field jumper), you have found the trouble. Always
follow-up with a voltage regulator test.

Test and Adjust Voltage Regulator Setting

1. Always test alternator output first, as

subparagraph a above. Leave all test
connected, but make sure field

is removed; if

used.

2. With engine speed at

RPM, turn tester con-

trol

knob

OHM” position. Make sure

electrical accessories are turned off. After
reading stabilizes, any reading between 13.5 and 14.5
volts is okay.

3. If voltage reading is out of limits, remove regulator

cover and adjust voltage regulator armature spring
tension to obtain a middle reading of 14.0 volts. If

reading fluctuates, voltage contacts are dirty.

4. Replace regulator cover and recheck voltage set-

ting. A steady voltage reading between 13.5 and 14.5
volts means voltage regulator is okay.

5. Adjust engine speed to specified idle. Reseal volt-
age regulator cover carefully, using electrical tape.

MAJOR REPAIR

ALTERNATOR OVERHAUL

Always disconnect battery ground cable before mak-
ing any electrical repairs.

Alternator Removal

1. Disconnect battery ground strap.

2. Unplug wiring connector from alternator.

3. Disconnect battery lead from alternator.

4. Remove adjusting brace bolt, lockwasher, plain
washer and nut.

5. Loosen pivot bolt. Push alternator inward and
remove belt from pulley.

6. Drop alternator down and remove pivot bolt, nut,

and plain washer.

7. Remove alternator.

Figure 1D-6 Removing Alternator Pulley

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1900 1973

Отзывы:

Opel 1900 1973, Руководство по обслуживанию, Страница: 51 / 625

Результаты поиска

Содержание 1900 1973

Отзывы: