Opel 1900 1973 Скачать руководство пользователя страница 568

Страница: 568 / 625

REFRIGERANT COMPONENTS ALL MODELS

2. If the receiver-dehydrator has been exposed to

the atmosphere for any amount of time, (more than
5 minutes), the receiver-dehydrator should be re-

placed, since the life of the dessicant is probably
expended.

3. Evacuate and charge system. Refer to CHARG-

ING AND DISCHARGING SYSTEM.

REMOVAL AND INSTALLATION OF EVAPORATOR
AND EXPANSION VALVE. GT

Removal

1. Disconnect negative battery cable.

2. Discharge system. Refer to, DISCHARGING

SYSTEM.

3. While system is discharging, remove attaching

screws and lift out luggage tray. See Figure

Figure

Evaporator Cover Assembly and

Attaching Screws GT

Figure

Luggage Tray

4. Remove all evaporator cover screws and remove

cover. See Figure

5. Remove electrical plug connector from the resis-

tor assembly and unplug blower motor connection

and remove ground wire. See Figure

6. From underneath evaporator housing, discon-

nect two (2) drain hoses. See Figure

7. From under car remove 4 nuts securing

Figure

Electrical Connections, Ground Wire

mounting bracket to floor. See Figures

and

8. Remove inlet and outlet pipes from evaporator

and tape closed the refrigerant lines and also the
open ends of the inlet and outlet pipes of the evapora-

tor. See Figure

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды

Opel 1900 1973, Руководство по обслуживанию

Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды