Opel 1900 1973 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 625

Opel 1900 1973 Скачать руководство пользователя страница 45

1

24

1973 OPEL

MANUAL

2. Push retaining ring out of groove in

shaft. See Figure

3. Push up on distributor shaft. Remove breaker

plate from distributor housing. Remove breaker
points from breaker plate. See Figure

1.

Figure

1 Removing Breaker Plate

4. Disassemble breaker plate by unscrewing
thrust spring screw. Remove spring and ball.
Figure

5. For cleaning, partly pull distributor shaft together
with centrifugal advance mechanism out of distribu-
tor housing. Do not disassemble advance mech-

anism.

6.

and check all parts. Replace any defective

parts.

7. Coat sliding parts of centrifugal advance mech-

anism and return springs with grease. See “A” in
Figure

13.

Figure

Lubricating Centrifugal Mechanism

Reassembly

Install new breaker points on breaker plate.

2. Install retaining ring on distributor shaft.

3. Install vacuum units, ignition condenser and cap
retaining

Figure

Disassembling Breaker Plate

Figure

Lubricating Upper Distributor

«
...
43
44
45
46
47
...
»

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов