Opel 1900 1973 Скачать руководство пользователя страница 486

Страница: 486 / 625

AUTOMATIC TRANSMISSION

1. CASE VENT

CLUTCH

7. SUCTION

2. CONVERTER OUT

8. LINE

CLUTCH

6. BOOST

9. REVERSE

Figure

Case Front View Oil Passage

Identification

reaction sun gear drum bushing sleeve

inside case at rear for scoring. If necessary, replace
sleeve before installing rear case bushing.

8. Remove sleeve by grinding. Care must be used in

order that aluminum case is not damaged when
grinding sleeve.

9. Install new sleeve using installer tool J-23130-7
and driver handle J-8092.

10. Install new case bushing using remover and in-

staller tool J-23130-3 and driver handle J-8092.

Bushing should be installed flush with case at rear.

See Figure

Figure

1. Drain Converter. If clutch disc material or

foreign matter has been found while draining con-
verter,
replace entire converter assembly as it can not be
cleaned properly.

2. Air check converter for leaks using converter

checking tool J-21369. Install tool and tighten. Ap-

ply 80 psi air pressure to tool. See Figure

Figure

3. Submerge in water and check for leaks.

4. Check converter hub surfaces for scoring or wear.

Installation of Selector Lever and Shaft

1. Install new selector lever shaft oil seal in case.

Insert selector lever shaft through case from outside.

Care should be exercised so that oil seal is not da-
maged. See Figure

2. Insert spring pin in case to secure selector lever

shaft.

3. Guide selector lever over shaft and secure with

lock nut.

4. Insert parking

actuator rod from front of the

case and through hole in case at rear. See Figure
207.

5. Install parking

actuator rod retaining ring.

Installation of Low Band

1. Turn transmission case so that front of case is

upward.

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды

Opel 1900 1973, Руководство по обслуживанию

Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды