Opel 1900 1973 Скачать руководство пользователя страница 265 | Manualshive

Страница: 265 / 625

background image

6

1973 OPEL SERVICE MANUAL

ing on dusty and sandy roads the filter and sound
deadener should occasionally be replaced. To do so,
brake booster has to be removed without detaching

brake master cylinder.

Proceed as follows:

Remove protective cap (boot).

2. On the GT only, pry retainer from housing
using a screwdriver. See Figure

Figure

Brake Booster Filter (GT)

3. With a pointed tool remove air silencer and filter

out of control housing bore and pull it off thrust rod.

4. Install new

and air silencer. On the GT, the

smooth side of the filter must face towards the inside.

The radial slots in filter and deadener must be stag-
gered to each other by 180 degrees.

5. Slide retainer over control housing (GT only) and
seal it with light plastic hammer strokes. Slide pro-
tective cap over control housing and slip it onto

brake booster housing.

VACUUM CONTROL VALVE SERVICE

A vacuum control valve is installed into the vacuum

hose between intake manifold and brake booster. It

serves to prevent air from flowing back (vacuum

release), when engine is shut off.

The vacuum control valve cannot be disassembled
and has to be replaced, if defective. On replacement,
note the following:

1. The vacuum control valve should

be

located near

the intake manifold. Therefore, the short vacuum

hose has to be installed between intake manifold and
vacuum control valve and the long hose between
vacuum control valve and brake booster.

2. The arrows on the vacuum control valve housing
must point towards the intake manifold, otherwise
no air can be drawn out of the brake booster which
renders the brake booster ineffective.

3. The connections of the vacuum hoses to the intake

manifold, vacuum control valve and brake booster
must be airtight. For this reason make sure. that the
hose clamps are properly installed.

MAJOR REPAIR

BRAKE BOOSTER REMOVAL

AND INSTALLATION

Removal

Disconnect brake pipes from master cylinder.

Place a cloth under the master cylinder and brake
pipes

to

absorb any brake fluid drippings.

2. Disconnect vacuum hose from brake booster.

3. Remove four nuts and washers attaching brake
booster to brake booster support.

4. On the GT only, remove master cylinder support
to fender skirt bolts.

5. On the GT, loosen thrust rod lock nut and un-
screw the piston push rod while holding the master
cylinder brake booster assembly. On the Opel
and Manta, remove the nut and bolt attaching
on the pedal.

6. Remove assembly from car.

Disconnect master cylinder from brake booster.

Installation

CAUTION:

Fasteners in the

steps are im-

portant attaching parts in that they could affect the

of

components and systems, and-

/or could result in major repair expense. They must

with one of the same part number or with

an equivalent part if replacement becomes necessary.
Do not

a replacement part or lesser quality or

substitute design. Torque values must be used as

specified during reassembly to assure proper reten-

tion of these parts.

1. Using a new front housing seal, assemble master

«
...
263
264
265
266
267
...
»

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1900 1973

Бренд: Jabra Страницы: 10

RadioPRO 5 RP5-GM41

Бренд: PAC Страницы: 3

Бренд: Vauxhall Страницы: 2

Бренд: Porsche Страницы: 144

Wireless Charging Station Universal

Бренд: BMW Страницы: 160

PERFECTVIEW CAM80AHD

Бренд: Dometic Страницы: 196

Бренд: AutoWatch Страницы: 4

Бренд: Atera Страницы: 10

4500 CHASSIS CAB 2012

Бренд: RAM Страницы: 7

Бренд: Nav TV Страницы: 5

Ram Commercial2016

Бренд: Dodge Страницы: 675

Бренд: Vauxhall Страницы: 259

HU-4421-XL-SDK01

Бренд: FALCON RIDGE Страницы: 5

Бренд: Flash Cover Страницы: 2

Бренд: Porsche Страницы: 98

Бренд: Prorack Страницы: 10

Бренд: Joie Страницы: 53

Бренд: Toyota Страницы: 779

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды