Opel 1900 1973 Скачать руководство пользователя страница 580

Страница: 580 / 625

COMPONENTS ALL MODELS

Figure

Removing Internal Cylinder Assembly

Figure

Removing Front Head

If sealing surfaces of front head (see Figure

13 1)

are damaged, replace front head. There is no Teflon
on front head sealing surface.

Disassembly of Cylinder Assembly

1. Pry off suction pass cover using screwdriver (see

Figure

assembly (front end downward)

on top of compressing fixture (J-9397), number pis-
tons and cylinders “1, 2 and 3” to facilitate reassem-
bly (see Figure

and separate cylinder halves

using a hard rubber mallet or hammer and wood

block.

SEALING

Figure

Front Head Sealing Surfaces

SUCTION
PASS COVER

Figure

Removing Suction Pass Cover

3. Disassemble rear cylinder half and discharge

tube from cylinder assembly and discard discharge
tube.

Depending on whether or not discharge tube comes

out with rear cylinder half or remains in front cylin-
der half it may be necessary to rotate shaft and
plate assembly (using a

inch opened wrench on

shaft seal portion of shaft) to achieve necessary

4. Carefully disassemble from cylinder assembly

(see Figure

and lay in respective place on

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1900 1973

Отзывы:

Opel 1900 1973, Руководство по обслуживанию, Страница: 580 / 625

Результаты поиска

Содержание 1900 1973

Отзывы: