Opel 1900 1973 Скачать руководство пользователя страница 182

Страница: 182 / 625

FRONT SUSPENSION

SHOCK ABSORBER REMOVAL AND
I N S T A L L A T I O N

Removal

Manta

1. Raise car and support with stands.

Remove upper attaching nuts from shock ab-

sorber.

3. Remove lower attaching nut, lockwasher, and
bolt.

4. Compress shock absorber and remove from car.

Removal GT

1. Remove air cleaner. See Figure

Figure

Removal of Air Cleaner

2. Remove plastic cover over shock absorber upper
attachment.

3. Raise car and support with stands.

4. Remove upper attaching nuts from shock ab-
sorber.

5. Remove lower attaching nut, lockwasher, and

bolt.

6. Compress shock absorber and remove from car.

Installation Opel

Manta

1. Inspect shock absorber for damage and seal leaks.

Always replace the upper and lower rubber grom-
mets when replacing a shock absorber.

2. Install the lower grommet retainer and grommets
on shock absorber. Compress shock absorber and
place in position.

3. Install lower attaching bolt and nut. Torque to 30

4. Install nuts on upper attaching studs. Tighten nuts
until distance from top of nut to stud is approxi-
mately

inch. See Figure

5. Install plastic cover.

Installation GT

1. Inspect shock absorber for damage and seal leaks.

Always replace the upper and lower rubber grom-
mets when replacing a shock absorber.

2. Install the lower grommet retainer and grommets

on shock absorber. Compress shock absorber and
place in position.

3. Install lower attaching bolt and nut. Torque to 30

ft.

4. Install nuts on upper attaching studs. Tighten nuts
until distance from top of nut to stud is approxi-
mately

inch. See Figure

5. Install plastic cover.

6. Install air cleaner.

FRONT SPRING REMOVAL AND INSTALLATION

Removal

1. Raise car and support at rear of front frame rails

with stands.

2. Remove front wheels.

3. Remove cotter pin from castle nut on lower ball

joint studs and back off castle nut two (2) turns. Hit

ball stud a sharp blow to break it loose.

Do not

nut.

4. Install J-21689 spring compressor and compress
the spring until

clearance is obtained between

spring and compressor.

5. Disconnect both shock absorbers at their lower

attachment. Compress both shock absorbers.

6. Support the rail of J-21689 Spring Compressor
with a jack. Remove lower control arm to cross
member attaching nuts and bolts.

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды

Opel 1900 1973, Руководство по обслуживанию

Результаты поиска

Содержание 1900 1973

Отзывы:

Похожие инструкции для 1900 1973

Бренды по названию

Популярные бренды