manualshive.com logo in svg

Opel 1900 1973, Руководство по обслуживанию

Сервисное руководство Opel 1900 1973 года поможет вам самостоятельно решить любые проблемы с вашим автомобилем. Загрузите бесплатное руководство с {веб-сайта} и получите доступ к детальной информации о техническом обслуживании и ремонте вашего Opel 1900 1973 года. Не беспокойтесь о дорогих ремонтах - скачайте руководство прямо сейчас!

Поделиться
Скачать
background image

  2 8   1 9 7 3   O P E L  

  M A N U A L

 SYSTEM

DESCRIPTION 

 OPERATION‘:

Alternator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

R e g u l a t o r

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . . .

DIAGNOSIS: (Not Available):
MAINTENANCE AND ADJUSTMENTS:

Alternator Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulator Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAJOR REPAIR:

Alternator

Removal

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Alternator

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Alternator Reassembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Alternator

Installation

. . . . .   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SPECIFICATIONS:

Alternator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Regulator . . . . .  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 

1 D-28

1 D-29

1 D-29

1 D-29

1 D-30

1 D-34

1 D-35

 D-35

1 D-35

DESCRIPTION AND OPERATION

ALTERNATOR DESCRIPTION

 

 35 amp alternator is standard equipment on

all 1973 models.

Figure 

 Alternator Installed

The alternating current generator (alternator) is a
continuous-output (even at idle), diode rectified gen-
erator. See Figure 

The rotor, which carries the field winding, is

mounted in ball bearings at both ends. Each bearing

has a sealed-in grease supply which eliminates the
need for periodic lubrication. Two brushes and two
slip rings are used. One brush conducts the current
provided by the voltage regulator to one end of the
field coil; the other brush conducts the current from

the other end of the rotating field coil to ground.

The three phase 

 windings are assembled on the

inside of a laminated core that forms the center sec-
tion of the alternator frame. Nine rectifier diodes are
connected to the 

 windings (three to each phase

lead). The diodes change the alternator AC voltages
to DC voltage coming out of the B positive and the
D positive terminals of the alternator.

If the alternator will not meet output specifications
when supplied with full field current, the 

assembly

must be overhauled. If the voltage regulator does not
limit maximum voltage within specifications, adjust
the voltage regulator. If steady voltage regulation,
within specifications, cannot be achieved, the voltage
regulator assembly must be replaced.

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1900 1973

cam 2850 Mounting Instructions preview
2850
Бренд: cam Страницы: 2
Dapper Lighting 575 Install Manual preview
575
Бренд: Dapper Lighting Страницы: 2
Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Бренд: Gardigo Страницы: 36
AMP Research 75135-01A Installation Manual preview
75135-01A
Бренд: AMP Research Страницы: 12
Havis-Shields Half Size Trunk Box Organizer C-TBO-CV Installation Instructions preview
Half Size Trunk Box Organizer C-TBO-CV
Бренд: Havis-Shields Страницы: 1
Volvo S60 2012 Quick Manual preview
S60 2012
Бренд: Volvo Страницы: 8
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Бренд: Ford Страницы: 38
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Бренд: KRAFTWERK Страницы: 2
Ford 2004 Freestar Workshop Manual preview
2004 Freestar
Бренд: Ford Страницы: 8
Intec CVD500LCD Installation And Operation Manual preview
CVD500LCD
Бренд: Intec Страницы: 16
Whispbar K919W Fitting Instructions Manual preview
K919W
Бренд: Whispbar Страницы: 17
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Бренд: VER-MAC Страницы: 64
SAN HIMA SGBR015 Installation Instructions Manual preview
SGBR015
Бренд: SAN HIMA Страницы: 10
ConWys AG 21500598C VW Fitting Instructions Manual preview
21500598C VW
Бренд: ConWys AG Страницы: 16
DFI VC230-BT Installation Manual preview
VC230-BT
Бренд: DFI Страницы: 6
Jaeger 12160509J Fitting Instructions Manual preview
12160509J
Бренд: Jaeger Страницы: 16
rough country RCH5100 Installation Instructions preview
RCH5100
Бренд: rough country Страницы: 4
Volvo S40 2001 Owner'S Manual preview
S40 2001
Бренд: Volvo Страницы: 197

Бренды по названию

Популярные бренды

Загрузить еще бренды