Opel 1900 1973 Скачать руководство пользователя | Manualshive

Страница: 309 / 625

background image

18 1973 OPEL SERVICE MANUAL

pressure. If heavy pressure is required, shell was not

started squarely and will be distorted if force into

place.

12. Place lower bearing shell in bearing cap, then

check clearance

plastic-type gauge, as previ-

ously described.

13. The desired clearance with a new bearing is

to

If this clearance cannot be obtained

with a standard size bearing, insert an undersize
bearing and check again

plastic-type gauge

material.

14. When the proper size bearing has been selected,

clean out all plastic gauge material, oil the lower
shell and reinstall bearing cap. Clean the bolt holes
and lube bolts, then torque cap bolts to 72 lb. ft. The
crankshaft should turn freely at flywheel rim; how-
ever, a very slight drag is permissible if an undersize
bearing is used.

15. If the thrust bearing shell is disturbed or replaced

it is necessary to line up the thrust surfaces of the
bearing shell before the cap bolts are tightened. To
do this, move the crankshaft fore and aft the limit of
its travel several times (last movement fore) with the
thrust bearing cap bolts finger tight.

16. After bearing is installed and tested, loosen all

bearing cap bolts

turn and continue with other

bearings. When bearings have been installed and
tested, tighten all bearing cap bolts to 72 lb. ft.

17. Replace rear bearing oil seals.

18. Install pipe and screen assembly and oil pan.

Installation of Rear Bearing Oil
Seals (Engine in Vehicle)

1. Remove transmission, bell housing and clutch.

Refer to appropriate section for removal procedures.

Figure

Removing Rear Main Oil Seal

2. Remove flywheel.

3. Punch a hole into oil seal and screw in a sheet
metal screw and pull out oil seal. See Figure

4. To insure proper sealing, lubricate seal with a
suitable protective grease and install on taper ring
J-22928. Turn seal to ensure lip of seal is not turned
back. See Figure

OIL SEAL

Figure

Installing Oil Seal on

Tool J-22928

5. Place tapered ring with oil seal on crankshaft

flange and move lip of seal

rear of crankshaft.

Be careful not to tilt seal.

Figure

Installing Rear

Main Bearing Oil Seal

6. Drive in oil seal using Tool J-22928-2. See Figure

7. Install flywheel, clutch, bell housing and

«
...
307
308
309
310
311
...
»

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1900 1973

Бренд: Saab Страницы: 10

2012 Escalade Hybrid

Бренд: Cadillac Страницы: 90

Бренд: Masterack Страницы: 4

Бренд: Over Armour Offroad Страницы: 5

Бренд: Cadillac Страницы: 407

Бренд: Mazda Страницы: 122

Бренд: Mercedes-Benz Страницы: 358

Бренд: Volvo Страницы: 211

ULTIMATE SPEED 296713

Бренд: walser Страницы: 10

Бренд: Mercedes-Benz Страницы: 373

Бренд: Saab Страницы: 9

Бренд: Prime Design Страницы: 12

Gigaware 12-493

Бренд: Gigaware Страницы: 8

Бренд: Yakima Страницы: 10

530 GRAN TURISMO - 2010

Бренд: BMW Страницы: 26

Бренд: AL-KO Страницы: 88

Бренд: Whispbar Страницы: 42

Бренд: Chipolino Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды