manualshive.com logo in svg

Opel 1900 1973, Руководство по обслуживанию, Страница: 76 / 625

Поделиться
Скачать
Opel 1900 1973 Скачать руководство пользователя страница 76

 

 Horn Button and Contact

HAZARD; WARNING FLASHER

The hazard warning flasher is operated by the button
on the 

 of the steering column. When the button

is 

 down and released, all four turn signal

lights 

 flash. To turn the flasher system off, press

down 

 the 

 and release. When the hazard

warning 

 is operating, a flashing light in the

 cluster will operate. The hazard warning

flasher 

 is part of the directional signal switch.

 

 

WARNIN

G 

L I G H T

The 

 system warning light is located in the left

side of 

 instrument cluster assembly. The light

will 

 on when the brake pedal is depressed and

the ignition is on if there is a hydraulic leak in the
brake system. The light will go out when the foot is

 the brake pedal. The light will also

glow with the parking brake applied and the ignition
on. (On 

 transmission equipped vehicles,

light is   reminder to release parking brake; and on
manual 

 equipped vehicles, light glows

when 

 clutch pedal needs adjustment,)

SIGNAL 

The 

 light on the dash will show defects in

the directional signal system as follows:

1. 

 light on dash gives only one quick flash.

One of 

 switched-on directional signal lamp bulbs

is defective. The other signal lamp will continue to
flash. 

 most common defect is a burned out bulb.

2. 

 light on dash stays on when directional

signal 

 is switched to either side. Check flasher

unit. 

SIGNAL SYSTEMS

 55

MAJOR REPAIR

Removing and Installing Directional Signal Switch

Proceed as outlined in 

Group 3, Section E.

HORN REMOVAL

1. 

 grille (GT only).

2. 

Remove horn 

bracket 

attaching bolt.

3. Disconnect wires and remove horn.

Installation

1. Install horn with bracket attaching bolt.

2. Connect horn wire.

3. Install grille (GT only).

Removing Horn Contact

 Disconnect battery.

2. 

Remove horn cap.

3. Bend lockplate tabs down and remove steering
wheel nut, lockplate, and washer.

4. Mark 

shaft and wheel hub for reassembly align-

ment.

5. Remove steering wheel using Wheel Puller 

21686.

6. 

Remove horn contact from wheel.

installation

1. Replace horn contact.

2. Before installing steering wheel, lubricate return
pin and slide area on directional signal switch return
cams and contact ring.

3. With steering wheel properly aligned to shaft, in-
stall washer, lockplate, and nut. Torque nut to 15
lb.ft.

4. Bend up lockplate tab and install horn cap.

5. Connect battery.

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов