Opel 1900 1973 Скачать руководство пользователя страница 426

Страница: 426 / 625

Operation of Controls in Neutral Engine Running

Reverse Clutch Released

Third Clutch Released

Second Clutch Released

Locked

Low Band Released

Whenever the engine is running with the selector lever in Neutral, oil is pulled

the sump into the oil pump and dispensed

the pump under

The pressurized line oil if directed the priming

which bleeds the Line oil directed the

modulator

the

regulator

and the manual

The

is fed through the pressure regulator

the

oil from the converter being directed through the

back

into the

lubricating system.

Line oil directed the

modulator valve becomes regulated modulator

acts on the pressure regulator

the

downshift timing

the 1 2 accumulator

and the detent

The modulator oil passes through the detent valve act the 2 shift control

the 3 2

and the 2 3 shift control

Line oil

through the manual

and is regulated et the detent

regulator

before being directed

Low control

Summary

The converter is filled. the clutches and

band are released.

The transmission is in Neutral.

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1900 1973

Отзывы:

Бренды по названию

Популярные бренды

Opel 1900 1973, Руководство по обслуживанию

Результаты поиска

Содержание 1900 1973

Отзывы:

Бренды по названию

Популярные бренды