manualshive.com logo in svg

Opel 1900 1973, Руководство по обслуживанию, Страница: 393 / 625

Поделиться
Скачать
Opel 1900 1973 Скачать руководство пользователя страница 393

Figure 

 1 Position of Third, Fourth, and Reverse

Intermediate Lever on Selector Shaft

  2ND 

Figure 

 Position of First and Second

Intermediate Lever on Selector Shaft

3. Install spiral pins to secure both intermediate lev-

ers to the selector shaft. Spiral pins should not be
flush with lever surface, but rather should extend up
between 

 and 

 inches.

Installing Reverse Speed Shifter Intermediate

Lever and Interlock Balls, Springs, and Plugs

1. Engage reverse speed shifter intermediate lever

with third, fourth, and reverse intermediate lever 

and

also 

in slot in reverse gear shifter shaft, and install

1973 OPEL SERVICE MANUAL

bedding bolt through reverse speed shifter intermedi-
ate lever and into case. Reverse speed shifter inter-
mediate lever end play on bolt should be between

 and 

 inches.

2. Insert both interlock balls and then springs, and
drive both interlock plugs into case holes until they
bottom in interlock plug hole seats. Grooves in plugs
will be showing.

Installing Countershaft Gear Unit

1. Coat thrust washers with ball and roller bearing

grease and stick to transmission case. Lugs of thrust
washers must fit into transmission case slots. See
Figure 

2. Turn transmission case extension housing until
gear unit countershaft bore is completely exposed.

3. Place lock ball into shaft and from the rear of the
transmission insert shaft so that thrust washer is held
in position. Hold opposite thrust washer in position

by using a short drift.

4. Insert countershaft gear unit into transmission

case. Be sure all needle bearings and both needle
bearing washers are in place.

5. Insert gear unit countershaft into gear unit and

drive shaft into transmission case while driving out
Special Tool J-2291 1. Pay attention to lock ball. See
Figure 

Figure 

 Installing Countergear Shaft

Installing Transmission Case Extension Housing

1. Align transmission case extension housing and

gasket and torque (3) bolts with spring washers to 21
lb. ft.

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов