manualshive.com logo in svg

Opel 1900 1973, Руководство по обслуживанию, Страница: 270 / 625

Поделиться
Скачать
Opel 1900 1973 Скачать руководство пользователя страница 270

DISC BRAKES

 11

 

2. RUBBER FLUID 

6.

3. HOLLOW 

7.

AL5

3

Figure 

 Left Front Disc Brake   

 View

the piston circumference by its inherent tension. See
Figure 

 Both pistons are hollow. The open end

of each piston faces the brake disc.

A sheet metal spacer plate with two impressions for
preventing the piston from rotating is installed be-
tween each piston and friction pad and 

secured by

the friction pad dowel pins. The two friction pads are
positioned on the right and left of the brake disc
recesses in the caliper halves. Each friction pad con-
sists of a backing plate with friction material, which
is abrasive-coated, bonded to it. The friction pad
assemblies are held in position in the brake caliper by
two dowel pins, secured by slit dowel pin retainers,
and by a cross-shaped retaining spring which is 
loaded and positioned under the dowel pins, thus
pressing the friction pads and spacer plates firmly
against the pistons. The front brake line leading from

the brake master cylinder attaches to a distribution
tee from which a brake line leads to each front wheel
caliper. The caliper bores are interconnected by fluid
ducts within the caliper halves.

The front wheel disc brakes have self-adjusting pis-

tons. See Figure 

The adjustment of the pads is effected by the pistons

which push the friction pads ahead towards the
brake disc for a distance equivalent to the amount of
friction pad wear. This means that the greater the
wear the closer the pistons move 

towards 

the brake

disc. A running clearance exists between friction

pads and brake disc when the brakes are in “off”
position. This running clearance is provided 

by 

the

rubber fluid seals which are positioned in the caliper
half bores and which tightly grip and exert their
pre-load pressure on the pistons. The rubber fluid

seals also prevent the pistons from being pushed into

the caliper half bores more than the distance equiva-
lent to the running clearance. As the friction pads are

adjusted by the pistons, there must be no static pres-
sure in the front brake circuit when the brakes are in

 position. Non-existence of a static pressure in

the front brake circuit is achieved by eliminating the

check valve in the brake master cylinder on the front
brake circuit. During brake application the pressure
from the brake master cylinder is transferred to the
pistons in the brake caliper. The pistons move ahead
and press the friction pads against both friction 
faces of the rotating brake disc. The force exerted on
the brake pedal determines the pressure of the fric-
tion pads against the brake disc. On releasing the
brake pedal, the brake lines of the front brake circuit,
including the caliper half bores, are relieved of 

OPERATION

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов