Opel 1900 1973 Скачать руководство пользователя страница 557 | Manualshive

Страница: 557 / 625

background image

1973 OPEL SERVICE MANUAL

Condition

3. Compressor being

replaced with a

vice replacement
compressor major
oil loss evident.

Amount of Oil Drained

From Compressor

a. More than 4 oz.

Amount of 525 Oil to Install

In Compressor

a.

Same

amount as drained from

c o m p r e s s o r b e i n g r e p l a c e d .

4. Compressor being

rebuilt or repaired

no major oil loss
evident.

b. Less than 4 oz.

a. More than 1

oz.

b. Install 6 oz.

a. Same amount

drained from

compressor,

plus oz. additional.

5. Compressor being

rebuilt or repaired
major loss of oil
evident.

b. Less than 1

oz.

a. More than 4 oz.

b. Install 7 oz.

a. Same amount as drained from

compressor, plus 1

If foreign material is noted in oil drained from sys-
tem or evidence of moisture is obvious in the compo-
nents removed, it is recommended that the entire
system be flushed and the receiver-dehydrator be
replaced. A full oil charge of 10 oz. of 525 viscosity
refrigeration oil should be replaced in the system. It
should be noted that all service replacement com-
pressors will be supplied with 10

of oil. In most

cases it will be necessary to drain oil from service
replacement compressor and refill it with amount as
specified in the Oil Replacement Table.

filter screen on the expansion valve should be re-
placed. If the evaporator assembly is flushed while
installed in the car, the temperature bulb on the

evaporator

pipe must be disconnected to keep

the expansion valve from closing at the inlet source.

FLUSHING THE SYSTEM

It is recommended that dry nitrogen be used as a
flushing agent due to the low cost involved. In addi-
tion, dry nitrogen will not cause a temperature drop,
as in the case of refrigerant-12, which results in
thickening of refrigerant oil. Dry nitrogen has the
additional advantage of removing moisture from the
system.

Flushing of the system may involve all the compo-
nents of the system or individual components in the
system. The components may be flushed while
mounted in the engine compartment or may be
removed for flushing. When a component is not
removed, disconnect all refrigerant lines or hoses
attached to component. To perform flushing operat-
ion, connect a cylinder of refrigerant-12 to the com-
ponent to be flushed,

invert the cylinder and

open the cylinder valve so that the liquid refrigerant

pours out and through the component. When liquid
Refrigerant-12 reaches atmospheric pressure, it im-
mediately drops to minus 21.7 degrees F. Insure that
area immediately surrounding outlet of component is
clear of anything that may be damaged by contact
because of the sudden drop in temperature.

MAJOR REPAIR

REMOVAL AND INSTALLATION OF
COMPRESSOR OPEL 1900 MANTA

R e m o v a l

Remove negative battery cable from battery.

2. Remove air cleaner and heat pipe. Cover the

carburetor to keep out dirt etc.

3. Discharge system. Refer to DISCHARGING

SYSTEM.

In all cases where a complete system flushing operat-

4. While system is discharging remove sheet metal

ion is performed, the receiver-dehydrator and the

cover. See Figure

«
...
555
556
557
558
559
...
»

Содержание 1900 1973


















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1900 1973

Бренд: Prorack Страницы: 14

Бренд: Victory 4x4 Страницы: 13

Бренд: Maserati Страницы: 210

Бренд: OnStar Страницы: 22

MCL-7000 Series

Бренд: Dakota Digital Страницы: 2

Бренд: Volvo Страницы: 284

Бренд: HAUL MASTER Страницы: 8

Бренд: THIEYE Страницы: 88

Бренд: rockymounts Страницы: 6

Бренд: Prorack Страницы: 15

Бренд: Jeep Страницы: 292

Бренд: Whispbar Страницы: 14

Бренд: Westin Страницы: 3

Бренд: Kuda-Phonebase Страницы: 3

Turbocharger 15012

Бренд: Edelbrock Страницы: 1

Yukon XL Denali 2015

Бренд: GMC Страницы: 439

DH-RB 05.02 Series

Бренд: Dhollandia Страницы: 65

Бренд: ULTIMATE SPEED Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды