![background image](http://html1.mh-extra.com/html/omron/sysmac-ws02-cxpc1-ev3/sysmac-ws02-cxpc1-ev3_operation-manual_743554328.webp)
PART 3: CX-Server Runtime
CHAPTER 3 – Communications
OMRON
CX-Server Runtime_Page 16
Use the following procedure to change the PLC settings:
1, 2, 3…
1. Enter a name in the
Device Name
field. A device name must consist of no more than 32
characters and must be unique.
2. Select the device type of the PLC in the
Device Type
field. If the device requirement does
not appear in the list then CX-Server does not support it.
3. Further configure the device type (e.g. CPU number) by selecting the Device Type
Settings
pushbutton. Refer to
Chapter 3 - Device Type
Settings for further details.
4.
Select the network type of the PLC in the
Network Type
field. This list may include other
PLCs in the CX-Server project that can be used as gateway devices, depending upon the
device type chosen. A full list of connection types are provided below.
5.
Further configure the network settings (e.g. node number) if applicable by selecting the
Network Type
Settings
pushbutton. Refer to
Chapter 3 - Network Communications (End
Connection)
for further details.
6.
Optionally, enter a comment relating to this unique PLC in the
Comment
field.
7.
Select the
OK
pushbutton to save the new PLC or the
Cancel
pushbutton to abort the
operation.
Note
The Device Name must
not
contain any of the following characters: / \ : ; , ? *
& ! . “ but may include spaces and international characters. The Device Name is
case sensitive, i.e. if a name is entered in upper case which already exists in lower
case, a new PLC is created. The contents of the Network field depend upon the
device type settings of the new PLC. The Device Type
Settings
pushbutton is
disabled for the following devices: C20, FinsGateway, Memory Card Writer and
Programmable Read Only Memory (PROM) Writer, since these devices do not have
options. Any PLCs which have been set up and can act as a gateway device appear in
the
Device Type
field.
A full list of connection methods is as follows:
♦
SYSMAC WAY
.
♦
Toolbus
. Toolbus on the CS1-series PLCs allows CX-Server auto-baud rate detection up to 115,200 bps.
Toolbus on the CS1-series PLCs supports full
n
clients and
n
destinations.
♦
Modem via SYSMAC WAY
. Modem is supported through SYSMAC WAY communications via Windows
TAPI configuration.
♦
Modem via Toolbus
. Modem is supported through Toolbus communications via Windows TAPI
configuration.
♦
Ethernet via TCP/IP
. Ethernet is only supported for CS1-series PLCs, CV-series PLCs and
C200HE/G/X/E-Z/G-Z/X-Z series PLCs. All Ethernet connections now also support full
n
clients and
n
destinations via CX-Server Ethernet driver. CX-Server also utilises FinsGateway Version 3 Ethernet driver
if the required PLC connection UDP port is locked open by FinsGateway active running services.
♦
Controller Link for OMRON NSB
. Controller Link is supported through FinsGateway Version 3 when
installed via CX-Server installation and services are activated. CS1-series PLC Optical Controller Link is
supported via FinsGateway Version 3 when Controller Link is installed.
Содержание Sysmac WS02-CXPC1-EV3
