manualshive.com logo in svg

Notifier UniNet 2000, Инструкция по установке, эксплуатации и администрированию

Поделиться
Скачать
Notifier UniNet 2000 Скачать руководство пользователя страница 21

21

The Workstation Installation/Operation Manual  Version 2   Document 51540  Rev. B1  4/8/02

1.1.3 The Workstation Supervisor

The workstation supervisor is designed to monitor the workstation.  In the event that the software stops running or

the CPU fails, an onboard sounder is activated to notify operators of the problem.  The board also has an onboard

output relay to allow annunciation by any external device which uses dry contact inputs.  Alarms may be acknowl-

edged by pressing a button on the back of the board.
This board mounts internally in the UWS 586T computer using an ISA slot and a standard mounting bracket.

Power is provided by an external 24VDC source, power limited and regulated with battery backup which is UL/ULC

listed (as appropriate for your area) for use with fire protective signalling units.  The unit comes pre-installed and

configured and requires only external power to activate.  Maximum power use is 35mA @ 24VDC.

The onboard relay may be wired for normally open (NO) or normally closed (NC) operation by setting jumper JP1

to the desired position.  Refer to the board markings for jumper settings.  This relay is rated for 1A @ 30VDC.

Figure 1-7:  The WSSUP Board

NOTE:  Do not connect power from

a fire alarm panel, as it may cause a

ground fault in the panel.

Address Selection DIP

Onboard
Sounder

Acknowledge
Button

+ 2 4 V D C

Operation
Alarm LED

GND

Relay Output
(Use power limited
contacts only)

Jumper JP1

Содержание UniNet 2000









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды