Nortel Passport 7400 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 438

Nortel Passport 7400 Скачать руководство пользователя страница 89

89

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Chapter 14
Cable routing and labeling

Route and label cables prior to connecting the cables to the processor cards,
termination panels, and far-end equipment to simplify your installation tasks.

•

“Prerequisites to cable routing and labeling” (page 89)

•

“Cable routing and labeling task flow” (page 89)

Prerequisites to cable routing and labeling

•

Ensure all cables comply with the appropriate cable specifications. For
more information about cable requirements, including pinouts, see
241-7401-200 Passport 7400 Hardware Description.

•

Before routing any cables, measure the exact distance that the cables will
follow and ensure all cables are long enough, with minimal slack
management. Also, ensure that cables are routed away from anything that
can damage the cable or affect its signals.

Cable routing and labeling task flow

This task flow shows you the sequence of procedures you perform to route
and label cables. To link to any procedure, go to “Task flow navigation”
(page 90).

«
...
87
88
89
90
91
...
»

Содержание Passport 7400























































































































































































































































































































































































































































Отзывы:

Нет отзывов