Nortel Passport 7400 Скачать руководство пользователя страница 37

Страница: 37 / 438

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Chapter 3
5-slot Passport switch installation

Install a 5-slot Passport switch on the floor or in a rack or cabinet.

•

“Prerequisites to 5-slot Passport switch installation” (page 37)

•

“5-slot Passport switch installation task flow” (page 38)

•

“5-slot Passport switch installation supporting information” (page 41)

Prerequisites to 5-slot Passport switch installation

•

See “Unpacking a processor card” (page 426) for FP and CP handling
instructions.

•

Ensure you have completed all site preparations. For more information,
see “5-slot Passport switch installation supporting information”
(page 41).

•

If you are installing the switch in a rack or cabinet, ensure it has been
properly installed and grounded. For more information, see “Cabinet
installation” (page 81).

CAUTION

Risk of electrostatic damage

When handling processor cards, wear a grounded
antistatic wrist strap so that you do not damage electronic
parts. For more information, see “Avoid damage from
static electricity” (page 174).

Содержание Passport 7400























































































































































































































































































































































































































































Результаты поиска

Содержание Passport 7400

Отзывы:

Nortel Passport 7400, Установка оборудования, техническое обслуживание и устранение неисправностей, Страница: 37 / 438

Результаты поиска

Содержание Passport 7400

Отзывы: