Nortel Passport 7400 Скачать руководство пользователя страница 325

Страница: 325 / 438

Chapter 37 Hardware procedures 325

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Removing a 13” termination panel from a 3-slot Passport
switch

Remove a termination panel to replace a failed panel or if you are removing
its associated FP(s) from the shelf.

Procedure navigation

•

“Procedure steps” on page 325

•

“Procedure job aid” on page 326

Procedure steps

Label the cables connected to the termination panel. Then, remove the
cables and coil them carefully out of the way.

Remove the screws at the ends of the termination panel that hold the
panel in position. See the figure “3-slot Passport switch termination panel
removal” (page 326).

Replace the screw that you removed in step 2.

Содержание Passport 7400























































































































































































































































































































































































































































Результаты поиска

Содержание Passport 7400

Отзывы:

Nortel Passport 7400, Установка оборудования, техническое обслуживание и устранение неисправностей, Страница: 325 / 438

Результаты поиска

Содержание Passport 7400

Отзывы: