Nortel Passport 7400 Скачать руководство пользователя страница 315

Страница: 315 / 438

Chapter 37 Hardware procedures 315

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Powering up a 5-slot Passport switch

Power up a 5-slot Passport switch after installing all hardware and cabling.

Prerequisites

•

install cabinet or switch shelving

•

install cooling unit equipment

•

install power supplies (in standby mode)

•

install termination panels, if required

•

install customer-equipment cables, if required

•

install control processors (CP) and function processors (FP) in the
disengaged position

•

install card cables

•

install power cords

•

install external alarm cables (for cabinet installations only)

Procedure steps

Connect and wear the antistatic wrist strap.

Make sure that all power supply switches are in the standby position. See
the figure “5-slot Passport switch power supply” (page 317).

Ensure that the CP in slot 0 and all FPs are engaged.

Turn on the circuit breakers for the outlets that supply power to your
switch.

Verify that the LEDs on all power supplies are red.

Apply power to one of the power supplies by setting its power switch to
the on position. See “5-slot Passport switch power supply” (page 317).

CAUTION

Risk of equipment damage

You can damage equipment if you power up a switch
before you have met the prerequisites listed in
“Prerequisites” (page 318)

Содержание Passport 7400























































































































































































































































































































































































































































Результаты поиска

Содержание Passport 7400

Отзывы:

Nortel Passport 7400, Установка оборудования, техническое обслуживание и устранение неисправностей, Страница: 315 / 438

Результаты поиска

Содержание Passport 7400

Отзывы: