Nortel Passport 7400 Скачать руководство пользователя страница 389 | Manualshive

Страница: 389 / 438

Nortel Passport 7400 Скачать руководство пользователя страница 389

Chapter 37 Hardware procedures 389

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Replacing a 16-slot Passport switch air filter

Replace a 16-slot Passport switch air filter pad every two months.

Prerequisites

•

You will need an air filter with PEC A0383866.

•

The 16-slot Passport switch has two kinds of air filter assemblies. The
spring-loaded air filter assembly displays the label “Air filter, press to
release.” The air filter assembly that is not spring-loaded displays the
label, “Air filter, remove cooling unit drawer first.”

Procedure steps

1

If the air filter assembly is spring-loaded, carefully press and release the
center of the air filter cartridge. This action disengages the air filter
assembly.

or

If the air filter assembly is not spring-loaded, remove the cooling unit
drawer. See the procedure.“Removing a 16-slot Passport switch cooling
unit” (page 350).

2

Carefully pull the air filter assembly out of its slot. See the figure
“Removing a 16-slot Passport switch air filter assembly” (page 391).

3

Turn the air filter assembly so that the bottom side faces up. See the figure
“Changing a 16-slot Passport switch air filter pad” (page 392).

4

Open the filter gate.

5

Remove the old filter pad and replace it with a new filter pad.

6

Close the filter gate.

7

With the filter gate face down, slide the air filter assembly into its slot at
the top of the cooling unit chassis. See the figure “Installing a 16-slot
Passport switch air filter assembly” (page 393).

CAUTION

Risk of damage to equipment

Never operate a switch for longer than 30 minutes
without an air filter. The air filter protects the power
converters, CPs, and FPs from dust and particles.

«
...
387
388
389
390
391
...
»

Содержание Passport 7400























































































































































































































































































































































































































































Отзывы:

Нет отзывов