manualshive.com logo in svg

Nortel Passport 7400, Установка оборудования, техническое обслуживание и устранение неисправностей, Страница: 375 / 438

Поделиться
Скачать
Nortel Passport 7400 Скачать руководство пользователя страница 375

Chapter 37 Hardware procedures   375

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Removing a rack-mounted alarm panel

Remove a rack-mounted alarm panel if you need to replace a failed panel, or
if you do not want to use the panel any more.

Procedure steps

1

Disconnect the alarm panel cable from the alarm cable connector on the
alarm panel. See the figure “Rack-mounted alarm panel” (page 250).

Figure 144
Rack-mounted alarm panel

2

Remove the two screws that fasten the panel to the frame and remove the
panel.

3

Tape the grounding wire and the grounding strip to the termination panel.

4

Route the cable down the shelf assembly and disconnect it from the door
alarm connector on the back of the shelf. See the figure “Dual alarm shelf
interconnection” (page 377).

PPT 2497 001 AA

Power LED

Alarm cutoff

Minor alarm LED

Major alarm LED

•

•

•

•

•

•

•

•

Alarm cable 
connector

•

•

Содержание Passport 7400























































































































































































































































































































































































































































Отзывы:

Нет отзывов