Nortel Passport 7400 Скачать руководство пользователя страница 335 | Manualshive

Страница: 335 / 438

Nortel Passport 7400 Скачать руководство пользователя страница 335

Chapter 37 Hardware procedures 335

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Removing a 5-slot Passport switch cooling unit

Remove a 5-slot Passport switch cooling unit if the unit fails.

Prerequisites

Procedure steps

1

To unlock the door, use a 1/4-in. slot-head screwdriver to turn the locking
latch on the cooling unit door 1/4 turn counter-clockwise. See the figure
“16-slot Passport switch cooling unit lock” (page 351).

2

Open the door to access the cooling equipment.

3

If you have the newer model cooling unit, the wires that connect the fans
to the switch are at the front of the fan tray. Cut the tie wrap and disconnect
each connector. If you do not have the newer model, continue to the next
step.

4

Pull the front edge of the cooling unit toward you carefully. Remove the
cooling unit slowly.

CAUTION

Risk of equipment damage

Remove and restart cooling units in under 10
minutes.You can damage CPs and FPs and they can fail
if the fans are off longer than 10 minutes.

WARNING

Risk of injury by fan blades

Do not handle the fans while the blades are rotating. When
you remove a cooling unit, wait until the fan blades stop
before you continue.

WARNUNG

Verletzungsgefahr durch Lüfterblätter

Berühren Sie einen Lüfter niemals, während die Blätter
rotieren. Warten Sie bis zum vollständigen Stillstand der
Lüfterblätter, bevor Sie ein Kühlaggregat entfernen.

«
...
333
334
335
336
337
...
»

Содержание Passport 7400























































































































































































































































































































































































































































Отзывы:

Нет отзывов