Nordson Encore HD iControl System Скачать руководство пользователя

Страница: 52 / 93

Troubleshooting

4-12

Part 1603054-02

2015 Nordson Corporation

Meaning/Correction

Message

Error

Code

707

Powder high PWM

Powder air flow more than commanded value.
Check output of flow regulator (center regulator in pump

panel)

−

should be 85 psi. Check for kinked or blocked

powder delivery tubing. Check for blocked pump flow air

servo valve.

708

Pattern high PWM

Pattern air flow more than commanded value.
Check output of flow regulator (center regulator in pump

panel)

−

should be 85 psi. Check for kinked or blocked

powder delivery tubing. Check for blocked pattern flow air

servo valve.

Air Flow Re-Zero Procedure

Perform this procedure if the iControl gun control screens are indicating

pattern air flow when a spray gun is off and no air is actually flowing. This

procedure re-zeros the pump control cards to eliminate false air flow

indications.

Before performing a re-zero procedure:

Make sure the air pressure being supplied to the pump cabinet is higher

than the minimum 5.86 bar (85 psi).

Each pump circuit board in the pump cabinet controls two pumps and
the pattern air for two spray guns. Make sure no air is flowing through

the pumps, around the pump control manifold gaskets, or from around

any of the solenoid valves on the manifold. Re-zeroing boards when

leaks are present in the control manifolds will result in additional errors.

Re-Zero Procedure

See Figure 4-2. For each pump board that is being re-zeroed:

1. Disconnect the pattern air tubing controlled by the pump board from the

output fittings on the rear panel of the pump cabinet.

2. Plug the output fittings.
3. Record the board number and address settings of SW1 for each pump

board.

4. Set each address switch to zero.
5. Turn off the power to the pump cabinet, wait 5 seconds, then turn the

power back on.

6. Press and hold the TEST button on each pump board until the red fault

light turns on. Release the TEST button and wait for the red fault light to

turn off.

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды