Nordson Encore HD iControl System страница 59 Скачать руководство пользователя

Страница: 59 / 93

Troubleshooting

4-19

Part 1603054-02

2015 Nordson Corporation

Other In/Out Positioner Troubleshooting

Table 4-8 Other In/Out Positioner Troubleshooting

Problem

Cause

Correction

No movement from

in/out positioner in

response to move

command.

A fault has occurred

preventing operation.

Check the iControl alarm log.
Identify the fault and review the fault

troubleshooting information in this table.

Controller not configured

properly.

Contact Nordson technical support.

Configuration lockout applied

to in/out positioner.

Check the In/Out Positioner control screen for

the lockout indicator. Lockout is applied from

the Configuration screens.

iControl lockout applied to

guns, in/out positioners, and

reciprocators.

This is a normal condition unless a failure has

occurred. Refer to

Photoeye, Encoder, and

Interlock Troubleshooting

in this section.

Remote disable applied to

in/out positioner controller.

No status display on iControl

screens.

If Nordson USA ColorMax system:
Disable action is applied by a remote system

control panel keyswitch. In the Disable

position, the keyswitch opens the disable

input circuit at the in/out positioner controller.
No corrective action is required unless the

keyswitch Normal position does not allow

motion. Refer to your system drawings for

circuit details.
If not Nordson USA ColorMax system:
Apply jumper to force On the remote disable

input. Refer to system drawings for jumper

application.

No in/out positioner

response when Auto

mode selected.

A fault has occurred

preventing Auto operation.

Check iControl alarm screen.
Identify the fault and correct. Review the

related faults and corrections listed in this

table.

iControl in/out positioner

configuration settings have

not been completed.

Refer to Network Configuration and In/Out

Positioner Configuration in the iControl

Operator Interface manual. Make sure all

required settings have been made and are

correct.
Refer to the system electrical drawings and

make sure all connections have been made

correctly.

Continued...

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды