Nordson Encore HD iControl System страница 73 Скачать руководство пользователя

Страница: 73 / 93

Troubleshooting

4-33

Part 1603054-02

2015 Nordson Corporation

Touch Screen Failure

WARNING:

Do not spray powder with the iControl console door open

unless the console is out of the hazardous area surrounding any opening of

the spray booth. The hazardous area extends 3 feet outward from an

opening and continues in a 3 foot arc from the edge of an opening. Failure

to observe this warning could create a hazardous condition and could result

in personal injury or property damage.

Screens Display, but Touch Function Does Not Work

If the mouse pointer on the screen does not move to wherever you touch

the screen, touching buttons does not work, and the touch screen cannot be

calibrated, then the touch screen has failed. You must replace the iControl

PC.

Temporary Fix:

Shut off console power and connect a mouse with a PS2

connector to the MOUSE port of the left side of the iControl PC. Turn on

console power and allow the system to boot up. You should now be able to

use the mouse to point and click on screen buttons and data fields.

No Display

If the PC has power but nothing displays on the screen, then the screen has

failed. You must replace the iControl PC.

Temporary Fix:

Shut off console power and connect a VGA monitor,

keyboard, and mouse to the PC ports. Turn console power on. If the boot

screens and iControl screens display on the VGA monitor, you can use the

mouse to click on buttons and select fields and use the keyboard to enter

and change values.

Rotary Dial Troubleshooting

If rotating the dial on the keypad panel does not change the selected data

field value, the signal from the dial is not being received by the iControl PC.

If this happens, check the wiring connections from the keypad panel to the

iControl PC. If the connections are good, replace the keypad panel.

WARNING:

Do not spray powder with the iControl console door open

unless the console is out of the hazardous area surrounding any opening of

the spray booth. The hazardous area extends 3 feet outward from an

opening and continues in a 3 foot arc from the edge of an opening. Failure

to observe this warning could create a hazardous condition and could result

in personal injury or property damage.

Temporary Fix:

Perform a program shutdown and turn off console power.

Connect a standard PC keyboard with a PS2 connector to the KEYBOARD

port on the left side of the iControl PC. Turn on power and use the numeric

keys to enter values in selected data fields, or use the up and down arrow

keys to change field values. Replace the keypad as soon as possible.

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Похожие инструкции для Encore HD iControl System

Бренды по названию

Популярные бренды