Nordson Encore HD iControl System Скачать руководство пользователя страница 51

Страница: 51 / 93

Troubleshooting

4-11

Part 1603054-02

2015 Nordson Corporation

HDLV Pump Troubleshooting

For additional troubleshooting and repair information, refer to the pump

manual.

Pump Controller Error Codes

Table 4-5 Pump Controller Error Codes

Error

Code

Message

Meaning/Correction

571

System heartbeat

lost

Check circuit board connections.

572

5/24 volt power

Check circuit board connections.

573

Error writing to

internal EEPROM

Hardware error. Replace card.

574

Error reading to

internal EEPROM

Hardware error. Replace card.

575

Node address

changed from last

power up

Saved address does not match current address. Address switches were

changed. Informational message only.

576

Internal database

version changed

−

resetting to

defaults

An update to the database was detected and the current data is no

longer valid. Informational message only, operation should not be

affected.

577

Preset out of

range

The preset sent to the remote device was out of range. Check preset

settings and reset as required.

701

Pattern servo fault

The solenoid resistance was not detected or incorrect when the device

was not triggered. When the solenoid is not energized, the resistance of

the solenoid is checked by the system. These faults are generated if no

resistance is detected, or the correct resistance is not detected. Check

the proportional valve wiring connections. Check the solenoid operation.

Replace the valve if the solenoid is bad.

702

Pump servo fault

The solenoid resistance was not detected or incorrect when the device

was not triggered. When the solenoid is not energized, the resistance of

the solenoid is checked by the system. These faults are generated if no

resistance is detected, or the correct resistance is not detected. Check

the proportional valve wiring connections. Check the solenoid operation.

Replace the valve if the solenoid is bad.

705

Powder low PWM

Pump air flow less than commanded value.
Check for obstruction in pump air flow control valve. Clean valve as

described in pump manifold manual.

706

Pattern low PWM

Pattern air flow less than commanded value.
Check for obstruction in pattern air flow control valve. Clean valve as

described in pump manifold manual.

Continued...

Obsolete

Содержание Encore HD iControl System






























































































Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Бренды по названию

Популярные бренды

Nordson Encore HD iControl System, Руководство по оборудованию

Результаты поиска

Содержание Encore HD iControl System

Отзывы:

Бренды по названию

Популярные бренды